SM02 Pneumatic Vertical Shock Bump Test System

MENU
SM02 Pneumatic Vertical Shock Bump Test System
SM02 Pneumatic Vertical Shock Bump Test System

 
Pneumatic Vertical Shock Bump Test System

Pneumatic Vertical Shock Bump Test System

Product description

SM02 Pneumatic Vertical Shock Bump Test System is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
Features

Features

  • Pneumatic drive, simple structure and high reliability

  • Pollution free, without hydraulic leak risk and keep the environment clean.

  • Pneumatic drive greatly improves the shock test efficiency, maximum shock rate up to 120 times / min.

  • It can easily realize large pulse width and small overload test.

  • With a fast shock rate comparing to motor or hydraulic driven collision table, it has higher reliability and better collision waveform.

  • The speed and rate of shock can be easily controlled by adjusting the gas pressure.

  • SM90 series shock control and measurement system can perform manual shock, continuous shock, single shock, and interval shock.

  • Built-in brake mechanism ensures the safety of operation in any situation.

//v4-upload.goalsites.com/{
WE APPLY THE CONTROLLER DEVELOPED BY SANWOOD

WE APPLY THE CONTROLLER DEVELOPED BY SANWOOD

parameter

       Model SM0225 SM0250 SM02100 SM02200 SM02400 SM02600 SM02800 SM021000 SM022000
Parameters
Rated Load (kg) 25 50 100 200 400 600 800 1000 2000
Table Size (mm) 300×300 500×500 600×600 800×600 800×800 1000×800 1000×1000 1200×1200 1500×1200
Peak Acc. (G) Half-Sine 10850 10700 10300 10200 10100
Post-Peak 10200 10200 10100 1060 1050
Sawtooth
Trapeziod   15100 1560 1550
Pulse Duration (ms) Half-Sine 0.840 140 1.540 240 340 440 640
Post-Peak 318 618
Sawtooth
Trapeziod   612
Bump Waveform Half sine wave
Bump Peak Acceleration 501500 501000 50800 50600 50400
m/s2
Bump Pulse Duration (ms) 330
Overall Dimension (mm) 1400×1200 1600×1400 1700×1500 1700×1500 1900×1500 1900×1500 2000×1500 1900×1800 2200×1800
×2300 ×2300 ×2300 ×2300 ×2450 ×2450 ×2450 ×2550 ×2550
Weight (kg) 1000 1800 2500 2800 3800 4000 4800 5200 6000
Max. bump Rate 100 80 60 50 40 30 20
 (Times/Min)
Power Requirements for AC220V±10%50Hz2kVA
Table
Power AC220V±10%, 50Hz, 3kVA or AC380V±10%, 50Hz, 5kVA
Requirements for
Air Compressor
Air Source Air source output pressure is no greater than 1.0Mpa. If there is no air source in the lab, air compressor needs to be configured; if there is air source in the lab, and there is ahigh requirement for bump frequency times, a corresponding air tank needs to be configured.
Conditions
Working Environment Temperature range 0 ~ 40; Humidity ≤ 90% (25), non-condense
Standards MIL-STD-810F    IEC68-2-27

Product Catalog:

Send us a Message

We will contact you within 24 hours